In short:
- A gate or door that refuses to close is often doing exactly what it should: a safety beam is blocked, or the motor has sensed an obstruction too many times and shut down.
- Listen to the buzzer and watch the status light. Motor makers' guides explain what each pattern means, from low battery to multiple collisions.
- Use the manual release only as your motor's manual describes, with the gate or door stationary.
- Never adjust roller door springs or motor limits yourself. Springs are under tension all the time. Motors, springs, mechanisms and locks on gates and roller doors are all part of our work.
First, what kind of door or gate is it?
"Won't close" covers two quite different machines, and the checks differ:
- A sliding or swing driveway gate with a motor. A motor beside the gate drives it along a rack or arm. Most have a backup battery, an obstruction-sensing system and often infrared safety beams across the opening.
- A roller door or roller shutter. The curtain winds onto a drum above the opening, helped by springs, and may be motorised or hand-operated. You'll find them on garages at home, and on shopfronts, warehouses and industrial units.
Either way, roller shutter doors and gates, including their locks, mechanisms, springs, motors and gate motors, are part of our everyday repair work.
Why a motorised gate won't close
The user guide for one South African maker's range of sliding gate motors describes the behaviour behind most "won't close" calls. If the closing safety beam is broken while the gate is open, the gate can't be closed; if it's broken while the gate is closing, the gate stops and reopens. Separately, a collision counter tracks how often the gate hits something before it fully closes. Past the set limit, which defaults to four, the controller shuts down until it receives a valid trigger. Other makes work along similar lines, so check your own motor's manual.
| Cause | What you might notice | Safe to check yourself? |
|---|---|---|
| Safety beam blocked or out of line | Gate opens fine, won't start closing, or reverses | Yes: clear the beam path and look for a knocked beam post |
| Obstruction sensed repeatedly | Gate stops, reverses, then won't respond; buzzer beeps | Yes: clear the track and opening, then try the remote once |
| Stones or debris in the track | Gate stops at the same point every time | Yes, with the motor switched off or in manual mode |
| Low battery or no mains power | Slow, weak or no movement; status light or buzzer warning | Look and listen only; don't open the motor housing |
| A holiday or time-barring setting | Gate ignores remotes and beeps | Check your motor's manual for how the setting behaves |
| Limits out of adjustment | Gate or door stops short, or keeps running at the end | No: limits are set by a technician |
| Worn rollers, rack, springs or mechanism | Grinding, juddering, door hangs crooked | No: look only |
Safe checks before you call
- Clear the opening. Bins, a parked car's bumper, plants that have grown into the beam, a toy, a hosepipe across the track.
- Look at the beams. Is either beam unit knocked, wet or covered by a cobweb or leaves? Some have an indicator light that shows alignment; your manual will say.
- Count the beeps and watch the light. Write down the pattern and match it to your motor's manual: low battery, mains failure, multiple collisions, beam broken and holiday lockout all have different signals on many motors.
- Check for power. Are the house lights on? Has the plug or isolator for the motor been switched off? Don't go further than that with electrics.
- Try one trigger, not twenty. Pressing the remote repeatedly at a gate that's sensing an obstruction just adds to the collision count.
- Roller doors: look along the guides on both sides for anything bent or caught, and at the bottom rail for debris.
Don't open a gate motor's housing or reach into it. One maker's guide warns the unit can contain high voltages and tells owners to isolate the mains and disconnect the battery before cleaning or working on the system.
The manual release, used properly
Every motorised gate and garage door has a way to disconnect the motor so you can move it by hand. How it works differs by make: a key and thumbwheel behind a small door on many sliding gate motors, a pull cord on many garage door openers. Follow your manual exactly. In general:
- Make sure the gate or door is stationary and nobody is in its path.
- Release the motor as your manual describes and move the gate or door slowly by hand.
- If you have to leave a gate motor in manual mode, lock its access cover, as the maker suggests, and secure the gate another way.
- Re-engage the motor as the manual describes and test it with the remote while watching the gate.
Take extra care with a roller or garage door that's open or partly open when you release it. A door with a weak or broken spring can come down hard. If it feels unusually heavy, stop and leave it.
Springs and limits: leave them alone
A roller door's springs carry most of its weight, which is why a motor of modest size can lift a heavy door. That stored energy is also why springs are dangerous. A roller door maker's own care guidance says the spring is under tension at all times and can cause serious injury if an inexperienced person interferes with it, and that adjustments and repairs should be done with proper tools by trained people.
Limits, the settings that tell a motor where "fully open" and "fully closed" are, are the same story for a different reason. Set wrongly, a gate or door can drive into its end stops, strain the motor or close with more force than it should. One sliding gate motor maker also warns that collision sensing should only be switched off where extra safety devices, such as infrared beams and sensitive edges, are fitted. These are adjustments for a technician.
When to call, and what to tell us
Call when the gate or door still won't close after the safe checks, when the motor is silent, when it grinds or judders, when a roller door hangs crooked or a spring looks broken, or when you can't secure the property with it open. For a business, a shutter that won't come down at closing time is reason enough.
- Gate motor or roller door, and the brand on the motor cover if you can see it.
- The beep pattern and status light you noted.
- A short video of what happens when you press the remote.
- Whether you've used the manual release, and whether the gate or door is open or closed now.
- Where it is: a home driveway, a shopfront, an industrial unit.
Our guide on what to tell the locksmith when you call has more on photos and access. If a key has also broken off in the gate's pedestrian lock, see broken key in a gate lock.
Keeping gates and roller doors working
One sliding gate motor maker asks owners to check that obstruction detection and the other safety devices are working once a month, and lists simple six-monthly checks: keep the track clear of stones and dirt, make sure the wheels and rollers turn freely, keep plants away from the motor and rack, and check that the key still works the motor's cover lock. Roller doors benefit from the same habit: keep the guides clean and have the springs and mechanism looked at by someone trained when the door starts to feel heavy or noisy.
A gate motor's holiday setting is useful on an empty house, but make sure anyone arriving knows about it. Our article on being locked out of a holiday or weekend home covers that situation.
Roller shutters on shops in Paarl Central, doors on industrial units in Dal Josafat and driveway gates at family homes in Paarl South or Courtrai all come under the same care. We're a mobile locksmith in Paarl, open 24/7, with a R350 call-out and a quote on site before any work.
Questions
Can I leave the gate in manual mode overnight?
If you have to, lock the motor's access cover as the maker suggests and secure the gate another way, such as a chain and padlock. The gate isn't protected by the motor while it's disengaged.
Could it just be the remote?
Sometimes. If the gate works from a wall button or intercom but not the remote, the remote's battery is a likely suspect. We don't copy or program remotes; the motor's supplier or installer handles that.
Do you only fix the lock, or the motor too?
Both. Roller shutter doors and gates, including their locks, mechanisms, springs, motors and gate motors, are part of our normal services. The technician quotes on site before any work starts.
Need a locksmith to look at it?
If this hasn't solved the problem, our lock repairs service covers it. We're a mobile locksmith in Paarl, so we come to your door. Areas where this comes up often include Dal Josafat, Paarl Central, Paarl South.
Sources and further reading
- CENTSYS: D5-Evo, D10 and D10 Turbo sliding gate operator user guide (PDF) — Closing safety beams: an open gate can't close while the beam is broken, a closing gate stops and reopens; the collision counter (default four) shuts the controller down; buzzer and LED diagnostics; manual override and locking the access door; monthly safety-device checks and six-monthly maintenance; isolate mains and battery before working on the system.
- B&D New Zealand: Product care and installation — Door springs are under tension at all times and may cause serious injury if interfered with; adjustments and repairs by approved dealers with proper tools; don't use a door with faulty obstruction sensing.
- B&D Australia: How to manually open a B&D roller garage door — Pull the release cord until it clicks, take extra care if the door is open or ajar, and re-engage the opener afterwards.
- Census 2011: Dal Josafat Industrial sub-place, Paarl — Dal Josafat's census sub-place is an industrial area.